详细描述日本进口油研单向节流阀

IM电竞 

　企业QQ：2880626087

　电话；021-69001039

　手机；17321017802（微信）

　邮箱；17321017802@163.com

　地址：上海市嘉定区江桥嘉涌路99弄6号楼713室

CRGM-03-50 CRGM-03X-50 CRGM-06-50 CRGM-06X-50 CRGM-10-50 CRGM-10X-50

污染控制必须注意保持对液压油污染的控制，

否则可能导致液压油的破坏，并缩短阀门的使用寿命。

which satisfy the recommended viscosity and oil temperatures given above. 

Control of Contamination Due caution must be paid to maintaining control over contamination of the hydraulic fluids 

Rc 3/8 Rc 1/2 Rc 3/4 Rc 1 Rc 1-1 / 4 Rc 1-1 / 2

Slacken the lock nut and turn the flow adjustment knob anti-clockwise to throttle flow. 

 After achieving satisfactory performance tighten the lock nut.

液压油

TJ的粘度和温度2粘度范围在15 - 400 mm / s（77 - 1800 SSU）之间。

油温在-15 / + 70°C（5 - 158°F）之间。

使用满足上述给出的TJ粘度和油温的液压油。

which may otherwise lead t o breakdowns and shorten the life of the valves. 

 Please maintain the degree of contamination within NAS 1638-Grade 1 

松开锁紧螺母，逆时针旋转流量调节旋钮以调节流量。

压力平衡结构在高压调节时提供较少的努力。

2.  Use 25 ?m or finer line filter.

ONE WAY RESTRICTORS SRCT/SRCG-03/06/10 (3/8, 3/4, 1-1/4)

Fluid Types Any type of hydraulic fluid listed in the table below can be used 

约。质量kg（lbs。）

请保持NAS 1638-Grade 1内的污染程度

CRGM-03-5080 CRGM-03X-5080 CRGM-06-5080 CRGM-06X-5080 CRGM-10-5080 CRGM-10X-5080

3/8 BSP.F 1/2 BSP.F 3/4 BSP.F 1 BSP.F 1-1 / 4 BSP.F 1-1 / 2 BSP.F

CRGM-03-5090 CRGM-03X-5090 CRGM-06-5090 CRGM-06X-5090 CRGM-10-5090 CRGM-10X-5090

3/8 NPT 1/2 NPT 3/4 NPT 1 NPT 1-1 / 4 NPT 1-1 / 2 NPT

附件安装螺栓

子板可用。从上表中子板型号。

当不使用子板时，安装表面应具有良好的加工精加工。

 Pressure balanced construction provides less effort in adjustment at high pressure.

Recommended Viscosity and Temperatures 2  Viscosity ranging between 15 - 400 mm /s (77 - 1800 SSU).  

Oil temperatures between -15/+70°C (5 - 158°F).  Use hydraulic fluids 

2.使用25μm或更细的线路滤波器。

一路限制器SRCT / SRCG-03/06/10（3/8，3/4，1-1 / 4）

流体类型可以使用下表中列出的任何类型的液压油

This valve is used to regulate an actuator speed in a circuit where line pressure is almost steady 

and small fluctuation of o il flow due to pressure changes is permitted.

达到满意的性能后，拧紧锁紧螺母。

Attachment Mounting Bolts

Sub-plates are available.  Specify the sub-plate model number from the table above.  

When sub-plates are not used, the mounting surface should have a good machined finish.

该阀用于调节线路压力几乎稳定的电路中的致动器速度，

并且允许由于压力变化而导致的小流量波动。

集成止回阀允许从出口到入口的反向自由流动。

Integrated check valve allows reversed free flow from outlet to inlet port. 

详细描述日本进口油研单向节流阀